Shop Elcon-Models Shop Elcon-Models
Kategorien
Dokumentation

Bauanleitung Traxx 2WD

Bauanleitung Imp4ct 4WD

Bauanleitung Cleon MMX

Bauanleitung Dämpfer

Bauanleitung ByPass Dämpfer

Bauanleitung Airbrake

Luftbremse 3D 

Übersetzungsverhätnisse Cleon MMx

  Setups Cleon MMX

Baubericht Elcon Cleon MMX

Setup Elcon Imp4ct

RS5 Engine Modification Guide

RS5 LS-Diff 2 User Manual

RS5 XT Touring Car Manual Part 1

RS5 XT Touring Car Manual Part 2

RS5 Touring Car Parts List TX12-XT

SCS Powerlock Diff Montageanleitung

Bergonzoni Touringcar GT-S1 Explosionszeichnung Chassis

Bergonzoni TC Explosionszeichnung Vorderachse

Bergonzoni TC Explosionszeichnung Hinterachse


Artikelnummernsuche

Schnellsuche

Verwenden Sie Stichworte,um ein Artikel zu finden.
erweiterte Suche

Zylinderkit MRS Tuning 26cc

198.00 EUR 148.50  EUR

inkl. 20% MwSt., zzgl. Versand
Lieferzeit 5 Werktage

Tuned cilinder kit 26CC from MRS based upon the Zenoah. With cylinder- and piston porting.
Features: very low fuel consumption, high torque in lower rev area and reaches high RPM. Fully CNC machined.
Read before the directions of use for a long life time cycle and optimum performance.

?

The piston is machined inside and outside. Inside for a reduction of weight. Outside for an optimalisation of the flow of the fuel mixture. The piston has 4 extra transfer ports made in axial direction, which enlarges the area of flow and smoothens the flow of the fuel mixture towards the combustion chamber. Not only a higher volume can flow through, also lubrication is optimized, which pro longues the life time of the piston. The outside diameter directly above and under the piston ring is slightly trimmed. This results in a better lubrication of the piston ring and piston. As last modification, the top of the piston has been trimmed for compensating the increased compression as a result of the cylinder tuning.

The cylinder has been trimmed at the bottom to reduce the squish and setting the timing of the ports correct. The cylinder is mounted to the crank housing with liquid gasket. Inside the cylinder is only machined very little on the exhaust port, for timing purpose and maintaining a correct pulse. This helps to reduce the fuel consumption. At the transfer ports the eye-brows have been machined, inside the EFRA regulations set for inlet porting. Also the seperation wall of the transfer ports have been modified for higher volume and optimized flow properties of the fuel mixture. All modifications are carried out by CNC for repeatability and identical tuning on each engine.

Directions of use:

At first use, start with following needle settings of the carb:

L needle:  1 1/8 turn opened

H needle:  1 5/8 turn opened.

The first time let the engine iddle for about 10 minutes, after this cool down engine.

Drive with the engine for 10 minutes, do not open throttle more then 1/3rd, cool down engine.

Drive 2 tanks with around maximum 3/4rd throttle open.

Never let the engine rev towards the top end of its RPM when running in. When the engine is going to reach the top of its rev, directly go back to iddle.

CAUTION:

Always idle the engine for about 2 minutes and/or keep your RPM low when cold. This is essential, as the piston is highly modified and is of significant lower mass. Due to being less material present, the piston will heat up much quicker and so it expands quicker as well. Directly going high revs or running full throttle with a cold engine might lead to excessive wear and/or damage of the piston and/or cylinder.

?Lubrication 1:25 is advised using a full synthetical 2-stroke racing oil.


Artikelnr.:
970226
Gewicht:
1 kg
Herstellerartikelnr.:970226
Bestand: :verfügbar

Zylinderkit MRS Tuning 26cc
Für eine größere Darstellung klicken Sie auf das Bild.
Menge :
Artikel aus der selben Kategorie
Hebel für Vergaserwelle
Hebel für Vergaserwelle
3.00 EUR
inkl. 20% MwSt.

zzgl. Versand
Dichtung Original Vergaser
Dichtung Original Vergaser
1.50 EUR
inkl. 20% MwSt.

zzgl. Versand
Starterklinke G230/240/260/270, CY
5.10 EUR
inkl. 20% MwSt.

zzgl. Versand
Kunden die dieses Artikel gekauft haben kauften auch
Center Drive Shaft XL
Center Drive Shaft XL
37.50 EUR
inkl. 20% MwSt.

zzgl. Versand
Servo Doppelarm Alu  25Z
Servo Doppelarm Alu 25Z
12.90 EUR
inkl. 20% MwSt.

zzgl. Versand
Einweg-Differential
Einweg-Differential
128.75 EUR
inkl. 20% MwSt.

zzgl. Versand
Übersetzung
0 Artikel
Links
RC-Buggy-Racing Team Fehring
RC-Buggy Racing Track Brezi
1.RC Buggy Club Erfurt e.v

Bezahlservice Transferwise

Paypal



News


SKYPE CALL
Informationen
Versandkosten
Zahlungsmöglichkeiten
Datenschutz
Unsere AGB
Widerrufsformular
Kontakt
Newsletter
Gesamtübersicht
Impressum
zu den Favoriten


Copyright © 2020 Shop Elcon-Models / my-Warehouse Shopsystem, operated by STAPIS GmbH